PCM Connector Pin Out Chart (1997-1998 4.6L V8 Ford E150, E250)

1997, 1998 4.6L Ford E150 And E250 PCM 104 Pin Connector

The EEC-V powertrain control module (PCM) has a 104 pin connector. To aid you in correctly identifying the connector pins, the back side of the connector (wire side) is embossed with a few numbers.

APPLIES TO: The PCM connector pinout applies on to the following vehicles:

  • Ford E150 4.6L: 1997, 1998
  • Ford E250 4.6L: 1997, 1998

WIRE COLOR LEGEND: You can find the wire color legend here: PCM Connector Pinout Wire Color Legend.

PCM 104 Pin Connector
Pin Wire Color Description
 1 PPL/ORG Transmission Shift Solenoid 2
 2 PNK/LT GRN Check Engine Light (CEL)
 3 ORG/BLK Digital Trans Range (DTR) Sensor -1
 4 ---
 5 ---
 6 ---
 7 ---
10 ---
11 ---
12 YEL/WHT Fuel Pump Sending Unit
13 PPL Data Link FEPS
14 --
15 PNK/LT BLU Data Link (-)
16 TAN/ORG Data Link (+)
17 --
18 ---
19 ---
20 ---
21 DK BLU Crankshaft Position (CKP) Sensor (+)
22 GRY Crankshaft Position (CKP) Sensor (-)
23 ---
24 BLK/WHT Power Ground
25 BLK/LT BLU Case Ground
26 DK BLU/LT GRN Ignition Coil 1
27 ORG/YEL Transmission Shift Solenoid 1
28 ---
29 TAN/WHT Trans Control Switch
30 DK GRN Octane Adjust
31 ---
32 ---
33 PNK/ORG Vehicle Speed Sensor (VSS) (-)
34 ---
35 RED/LT GRN Bank 1 Sensor 2 O2 Signal
36 TAN/LT BLU MAF Sensor Signal Return (Ground)
37 ORG/BLK Trans Fluid Temp (TFT)
39 GRY Intake Air Temp (IAT) Sensor
40 DK GRN/YEL Fuel Pump Monitor (FPM)
41 BLK/YEL A/C Clutch Signal
42 BRN Intake Manifold Runner Control (IMRC)
43 ---
44 ---
45 YEL/LT BLU Engine Coolant Temp Gauge
46 BRN Intake Manifold Runner Control (IMRC)
47 BRN/PNK EGR Vacuum Regulator Solenoid Control
49 WHT/PNK Digital Trans Range Sensor -2A
50 GRY/BLK Digital Trans Range Sensor -4A
51 BLK/WHT Power Ground
52 RED/LT BLU Ignition Coil 2

WIRE COLOR LEGEND: You can find the wire color legend here: PCM Connector Pinout Wire Color Legend.

NOTE: You can find the 1999 4.6L Ford E150 and E250 PCM connector pinout here:

The PCM connector pinouts for the 1997 and 1998 Ford F150/F250 pickups can be found here:

1997, 1998 4.6L Ford E150 And E250 PCM 104 Pin Connector

Safety Precautions

Here are some very important safety precautions when testing the wires coming out of the 104 pin PCM connector.

  1. If one or any of the wires on your Ford van DO NOT match the color stated in the pin out charts, then you should not use the pin out charts in this article. Why? Because this is the clearest indication that these ARE NOT the connector pin out charts for your particular Ford pickup.
  2. Never probe the front of the connector.
    • You should use a wire piercing probe and probe the wire a few inches away from the connector.
    • You should use a back-probe.
  3. You should never disconnect any of the PCM connectors without first disconnecting the battery negative (-) terminal.


I've made every effort to double and triple check the above info (and in the next couple of pages) and I've used the best sources to compile it but nothing in life is perfect. I don't have a staff of proof readers or editors, I'm just a little guy typing this stuff up in my spare time to help and give back to the Do-It-Yourself community. So without further ado, here's my disclaimer:

© copyright Abraham Torres-Arredondo: This information is distributed in the hope that it will be useful, but WITHOUT ANY WARRANTY; without even the implied warranty of MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE.

If you do spot errors, please let me know. You can use the contact form at the end of the article.