How To Test Engine Compression (1995-2000 1.8L Mazda Protegé)

How To Test Engine Compression (1995, 1996, 1997, 1998, 1999, 2000 1.8L Mazda Protegé)

As the engine in your car starts to age and accumulate miles, the piston rings and cylinder head valves start to wear. Eventually they'll reach a point of wear and tear that'll cause engine compression problems.

These engine compression problems usually manifest themselves in one of two ways. Either your car is going to misfire or it's not going to start.

Thankfully, testing the engine compression, in your 1.8 Mazda Protegé, is not that hard. What makes the engine compression test easy is that the spark plugs are easy to remove. In this tutorial I'm gonna' teach you how to test it and more importantly how to interpret its results

In Spanish You can find this tutorial in Spanish here: Cómo Probar La Compresión Del Motor (1995-2000 1.8L Mazda Protegé) (at:

Symptoms Of Low Or No Engine Compression

As I mentioned at the beginning of the tutorial, engine compression problems fall into 2 different categories. Either the engine starts but misfires (runs rough), or the engine doesn't start at all.

In this section we're gonna' analyze both types of problems and see the specific symptoms they produce:

Engine Starts but Runs with a Misfire (Rough Idle):

  1. Also known as an engine miss, rough idle condition.
    • Usually caused by very low compression in one cylinder or...
    • Uneven engine compression that varies more than 15% across all 4 cylinders.
  2. Check engine light on with misfire codes:
    • P0300 Random Cylinder Misfire.
    • P0301 Cylinder #1 Misfire.
    • P0302 Cylinder #2 Misfire.
    • P0303 Cylinder #3 Misfire.
    • P0304 Cylinder #4 Misfire.
  3. Bad gas mileage.
    • This is caused engine not producing its optimal power output since the air/fuel mixture isn't being combusted with adequate compression pressure.
  4. Engine pollutes more.
    • If the air/fuel mixture isn't compressed within a certain range, it won't burn optimally and produce more unburned hydrocarbons escaping into the exhaust.

Your 1.8L Mazda Protegé won't start:

This usually is caused by having 2 or all 4 cylinders with no compression. When this happens, you'll see:

  1. The engine cranks very fast.
    • This fast cranking speed is very noticeable.
  2. The Ignition System is sparking all 4 spark plugs.
    • This tells you that the no-start condition is not caused by a fault in the ignition system.
  3. The fuel injectors spray fuel.
    • You can confirm this with a Noid Light test.
    • Also, you can confirm this, although indirectly, by removing the spark plugs and checking to see if they are fuel soaked (fuel fouled).
  4. Fuel pump is working and providing pressure.
  5. The most common causes of no compression on 2 or all 4 cylinders are:
    • Blown head gasket.
    • Broken timing belt.
    • Engine threw a rod.

OK, having covered the most common scenarios of low compression and no compression, let's get testing to see if this is the case on your 1.8L Mazda Protegé equipped vehicle.

Which Compression Tester Should I Buy?

There are lot of engine compression testers to choose from and many places to buy them. I'm gonna' make two recommendations to you:

1) Which one to buy:  The engine compression tester that I have always used is the Actron CP7827 Compression Tester Kit. My only complaint about this engine compression tester is that it does not come with a case to store it in.

2) Where to buy:  You can buy an engine compression tester just about anywhere, but you'll end up paying more for it (especially at your local auto parts store). The above links will help you comparison shop. I think you'll agree it's the better way to save money on the compression tester!

TEST 1: Finding The Dead Cylinders

How To Do An Engine Compression Test (1995, 1996, 1997, 1998, 1999, 2000 1.8L Mazda Protegé)

To get this show on the road, we'll start off by testing the compression of all four cylinders. In case you're wondering where you can get your hands on a compression tester, you can borrow one from your local auto part store, buy it from them, or, to save a few bucks, you can buy it on-line.

If you need help deciding where to buy one or which one to buy, take a look at my recommendations: Which Compression Tester Should I Buy?

Alright, to get the most accurate snapshot of the health of each cylinder its a good idea to start the engine and let it run for about 15 minutes and no more. Don't let it get hot. Or if it has been running for any length of time, let it cool down completely. You should not remove the spark plugs from a hot engine or you run the risk of stripping the spark plug threads in the cylinder head.

IMPORTANT: You'll be working around a cranking engine, so you have to be careful and stay alert at all times. Think safety all of the time!

This is what you'll need to do:

  1. 1

    If the engine starts, let it warm up for about 5 minutes, before you start this test (but don't let it get hot!).

    NOTE: If your Mazda doesn't start, then don't worry about the engine being warm.

  2. 2

    Disconnect all of the fuel injectors. This will prevent fuel from being injected into the cylinders as you crank the engine.

  3. 3

    Remove all four spark plugs

    As your taking them out, be careful and don't drop any of them on the floor, or you could cause the spark plugs ceramic insulator to break, and this will cause a misfire!

  4. 4

    Thread the engine compression gauge into the spark plug hole for the number 1 engine cylinder (this is the spark plug hole closest to the drive belt).

    Hand tighten the compression gauge only! Do not use any type of tool to get it tight.

  5. 5

    When the tester is set up, ask your helper to crank the engine. Your job is to keep your eye on the compression tester's gauge.

  6. 6

    Once the needle on the gauge stops climbing, have your helper stop cranking the engine.

  7. 7

    Write down the compression value on a piece of paper.

    Include the number of the cylinder this reading belongs to.

  8. 8

    Now repeat steps 4 thru' 6 on the other 3 cylinders.

Let's take a look at what your test results mean:

CASE 1: Low or no compression in 2 or all 4 cylinders. This test result indicates a serious internal problem.

The most common issues would be:

  1. Blown head gasket.
  2. Broken timing belt.
  3. Engine threw a rod.

CASE 2: Low or no compression in one cylinder.. Getting a no or low compression test result means you've found the cause of the engine's rough idle (misfire).

If you got a low compression reading, the next step is to find out if this reading is varying by more than 15% than the other cylinders (because if it is varying by more than 15%, then this cylinder is considered ‘dead’). To find out go to: Interpreting Your Compression Test Results.

Mazda Vehicles:

  • Protegé 1.8L
    • 1995,