How To Test The Intake Air Temp (IAT) Sensor (GM 4.8L, 5.3L, 6.0L)

TEST 5: Jumpering The IAT Sensor Circuits

How To Test The IAT Sensor (GM 4.8L, 5.3L, 6.0L)

So far, you have done the following: confirmed that you have a diagnostic trouble code (DTC) P0113: Intake Air Temperature (IAT) Sensor Circuit High Voltage.

Also, you've done TEST 1, where you've confirmed that the IAT sensor PID (on your scan tool) is registering a temperature of -30 to -40 °F.

The next step, is to use a jumper wire and jumper the two IAT sensor wires together. These two are the ones labeled with the letters A and B of the MAF sensor connector in the image viewer.

If all is OK in the wiring and in the PCM, after jumpering these two wires together the PCM will read a temperature of 300 °F and will set a DTC P0112: Intake Air Temperature (IAT) Sensor Circuit Low Voltage.

OK, here's what you'll need to do:

  1. Keep your scan tool connected to your vehicle.
  2. Disconnect the mass air flow (MAF) sensor from its connector.
  3. Locate the wires identified with the letter A and letter B.
    • Wire A is the Black wire.
    • Wire B is the Tan wire.
  4. Jumper these 2 wires together with a jumper wire.
  5. Turn the key to the ON position (RUN position)
  6. Let the scan tool power up and go to Live Data mode.
    • Scroll down to the IAT sensor PID (see photo 3 of 3).
  7. Your scan tool should now read 300 °F for the intake air temperature (IAT) sensor reading.
    • You'll also see DTC P0112.

Let's take a look at your test results:

CASE 1: The scan tool registered 300 °F - This test result tells you that the wiring between the PCM and MAF sensor connector is OK and that the PCM is not fried.

The next step is to check the internal resistance of the intake air temperature sensor to see if it has an 'open'.

For this test, go to: TEST 7: IAT Sensor Resistance Test (P0113).

CASE 2: The scan tool DID NOT register 300 °F. Make sure that you're testing the correct wires, that your connections are OK, and repeat the test.

Then this tells you that you have a problem in the wiring between the IAT sensor and the PCM or that the PCM is fried (although a bad PCM is rare).

The next step for you, is to make sure that the IAT sensor is getting power and Ground from its two wires. For this test, go to: TEST 8: 5 Volt Reference Circuit.

TEST 6: IAT Sensor Resistance Test (P0112)

How To Test The IAT Sensor (GM 4.8L, 5.3L, 6.0L)

In this test step, you're gonna check the resistance of the intake air temperature (IAT) sensor with your multimeter in Ohms mode.

This will check to see if the IAT sensor has shorted together inside the MAF sensor and causing a resistance between 0 and 47 Ohms.

If the intake air temperature (IAT) sensor is producing a resistance between 0 and 47 Ω's., then the PCM will output a temperature of 300 °F and set diagnostic trouble code (DTC) P0112.: Intake Air Temperature (IAT) Sensor Circuit Low Voltage.

OK, to get this test going, this is what you need to do:

  1. Disconnect the MAF sensor connector and remove the MAF sensor.
    • You don't have to remove the MAF sensor for this test, but I personally thinks it makes it a little easier to do this test with the MAF sensor removed.
  2. On the MAF sensor, locate the pins that correspond to the letters A and B of the MAF connector.
  3. With your multimeter in Ohms (Ω) mode:
    • Measure the resistance of the intake air temperature (IAT) sensor.

Let's interpret your test results:

CASE 1: The multimeter recorded 0 to 47 Ohms- This tells you that the intake air temperature (IAT) sensor inside the mass air flow (MAF) sensor is bad.

Since the IAT sensor is part of the MAF sensor, you'll need to replace the entire MAF sensor to solve the P0112 diagnostic trouble code.

CASE 2: The Multimeter DID NOT record 0 to 47 Ohms- So far so good, but you're not out of the woods yet.

The next step is to check the resistance you're getting to the temperature versus resistance chart in the next page.

The resistance should correspond to the outside temperature (ambient temperature) of your area. For this info, go to: IAT Sensor Temperature/Resistance Chart.

TEST 7: IAT Sensor Resistance Test (P0113)

How To Test The IAT Sensor (GM 4.8L, 5.3L, 6.0L)

In this test step, you're gonna check the resistance of the intake air temperature (IAT) sensor with your multimeter in Ohms mode to see if the IAT sensor is bad.

What you're gonna' do, is to see if the IAT sensor is 'open' by doing a resistance test and using the 'IAT Sensor Temperature to Resistance' chart found here: IAT Sensor Temperature / Resistance Relationship (which, by the way, is in the next page).

OK, to get this test going, this is what you need to do:

  1. Disconnect the MAF sensor connector and remove the MAF sensor.
    • You don't have to remove the MAF sensor, but, it'll be easier to do this test with the MAF sensor removed.
  2. On the MAF sensor, locate the pins that correspond to the letters A and B of the MAF connector.
  3. With your multimeter in Ohms (Ω) mode:
    • Measure the resistance of the intake air temperature (IAT) sensor.
  4. What you're looking for, is to see if the IAT sensor records a resistance that indicates a temperature of -30 to -40 °F.
    • Specifically: What you're looking for, is a resistance that is at 100,700 Ohms (100.7 K Ohms) or more.
    • See the Temperature / Resistance Chart in the next page.

Let's interpret your test results:

CASE 1: The multimeter recorded a resistance of 100.7 K Ohms or more- This tells you that the intake air temperature (IAT) sensor inside the mass air flow (MAF) sensor is bad.

Since the IAT sensor is part of the MAF sensor, you'll need to replace the entire MAF sensor to solve the P0113 (Intake Air Temperature (IAT) Sensor Circuit High Voltage) diagnostic trouble code.

CASE 2: The Multimeter DID NOT record a resistance of 100.7 K Ohms- So far so good, but you're not out of the woods yet.

What you now need to do, is to see if the IAT sensor resistance equals to the ambient (surrounding) temperature of where you're testing your vehicle.

For example, if I'm testing my Chevy C1500 pickup outside and it's a balmy 95 °F. Then the temperature that the IAT sensor should record (in ohms of course) should be within ±10 °F of 95 °F. Using the Temperature / Resistance Chart in the next page, the IAT sensor resistance should be somewhere between 177 and 332 Ohms (0.177 and 0.332 K Ohms).

NOTE: If the IAT sensor checks out good (according the Temperature / Resistance Chart in the next page) The next step is to check that the IAT sensor is getting power, in the form of 5 Volts and Ground. For this info, go to: TEST 8: 5 Volt Reference Circuit.



Buick Vehicles:

  • Rainier 5.3L
    • 2004, 2005, 2006, 2007

Cadillac Vehicles:

  • Deville
    • 2001, 2002, 2003, 2004, 2005
  • Eldorado
    • 2000, 2001, 2002
  • Escalade
    • 2002, 2003

Cadillac Vehicles:

  • Seville
    • 2000, 2001, 2002, 2003

Chevrolet Vehicles:

  • Avalanche 5.3L, 8.1L
    • 2002, 2003, 2004, 2005
  • Silverado (1500, 2500, 3500)
    • 1999, 2000, 2001, 2002, 2003, 2004, 2005, 2006

Chevrolet Vehicles:

  • Suburban (1500, 2500)
    • 2000, 2001, 2002, 2003, 2004, 2005
  • Tahoe 4.8L, 5.3L
    • 2000, 2001, 2002, 2003, 2004, 2005, 2006
  • TrailBlazer 5.3L
    • 2003, 2004

GMC Vehicles:

  • Envoy 5.3L
    • 2003, 2004
  • Sierra (1500, 2500, 3500)
    • 1999, 2000, 2001, 2002, 2003, 2004, 2005, 2006
  • Yukon 4.8L, 5.3L
    • 1999, 2000, 2001, 2002, 2003, 2004, 2005, 2006

Hummer Vehicles:

  • H2 6.0L
    • 2003, 2004, 2005

Isuzu Vehicles:

  • Ascender 5.3L
    • 2003, 2004, 2005, 2006